Influência da orientação das ranhuras superficiais na flexão rotativa de fios de níquel-titânio / Influence of surface grooves orientation on the cyclic fatigue resistance of NiTi wire

Objetivo: Testar a hipótese nula de que a orientação das ranhuras superficiais não influencia na vida em fadiga de fios de níquel-titânio (NiTi). Material e Métodos: Segmentos de fio de NiTi (Moreli, Sorocaba/SP, Brasil) medindo 30mm e com diâmetro de 0,40mm foram utilizados. As ranhuras foram criadas em relação à direção longitudinal, em 45 e 90 graus. O fio foi analisado sob microscopia eletrônica de varredura e a rugosidade, quantificada por interferometria. O número de ciclos para a fratura (NCF) foi determinado pelo teste de flexão rotativa. Resultados: A rugosidade entre os grupos de 45 e 90 graus apresentou diferenças estatisticamente significativas (p<0,05). O grupo sem ranhuras apresentou o maior NCF (p<0,05). O grupo com ranhuras em 45 graus apresentou maior NCF, em comparação ao grupo com 90 graus (p<0,05). Conclusões: A direção das ranhuras possui influência na vida em fadiga dos fios de NiTi. O NCF aumenta com a redução do ângulo das ranhuras em relação ao longo eixo do fio, independentemente da profundidade das ranhuras (AU).

Objective: this study tested the null hypothesis that the surface grooves orientation does not influence the NiTi wire cyclic fatigue. Material and methods: Segments of NiTi wire (Moreli, Sorocaba, Brazil) measuring 30mm and with a 0.40mm of diameter were used. Grooves were created in the longitudinal direction, at 45 degrees and 90 degrees. The wire was analyzed with SEM and the roughness was quantified by interferometry. The number of cycles until fracture (NCF) was determined by the cyclic fatigue test. Results: the roughness between 45 and 90 degrees groups presented differences (p<0.05). The group without grooves presented the highest NCF (p<0.05). The group with 45 degrees grooves presented better NCF in comparison to the group with 90 degrees (p<0.05). Conclusions: the direction of the grooves influences the fatigue life. The NCF increases with the reduction of the angle of the grooves in relation to the long axis, regardless of the depth of the grooves (AU).

The impact of using a pneumatic contra-angle device on the lifespan of M-Wire- and Blue-treated instruments.

OBJECTIVES: To evaluate the cyclic fatigue resistance of Reciproc M-Wire R25 (VDW, Munich, Germany) and Reciproc R25 Blue instruments (VDW) driven by Direct® (VDW) contra-angle connected to an ordinary an air-driven motor or an electric motor and compare the results with those obtained by the Reciproc M-Wire R25 or Reciproc Blue R25 instruments driven by an electric torque-controlled motor using "RECIPROC ALL" preset program. MATERIALS AND METHODS: Thirty Reciproc M-Wire R25 (25/0.08v) and 30 Reciproc Blue R25 (25/0.08v) instruments were used. Cyclic fatigue resistance was tested measuring the time to fracture and the number of cycles to fracture in an artificial stainless-steel canal with a 60° angle and a 5-mm radius of curvature. The Reciproc M-Wire and Reciproc Blue instruments were activated with a 6:1 reduction handpiece powered by a torque-controlled motor using "RECIPROC ALL" preset program, with Reciproc Direct® contra-angle powered by an ordinary air-driven motor or with Direct® contra-angle powered by an electric motor (n = 10). The fracture surface of all fragments was examined with a scanning electron microscope. The results were statistically analyzed using Student's t test and one-way ANOVA at a significance level of P < 0.05. RESULTS: Cyclic fatigue life and number of cycles to fracture were significantly higher for Reciproc Blue instruments than for Reciproc M-Wire instruments regardless of the activation mode (P < 0.05). Instruments driven by Direct® contra-angle powered by an electric or by an ordinary air-driven motor revealed significantly longer cyclic fatigue life and number of cycles to fracture than instruments driven by an electric torque-controlled motor using "RECIPROC ALL" preset program (P < 0.05). CONCLUSIONS: Reciproc Blue instruments showed improved performance regarding fatigue resistance when compared to Reciproc M-Wire instruments. Instruments driven by Reciproc Direct® contra-angle showed higher cyclic fatigue life and number of cycles to fracture than instruments driven by an electric torque-controlled motor. CLINICAL RELEVANCE: Recently, Reciproc Direct®, the world's first contra-angle handpiece with integrated reciprocating motion, has been launched in endodontic market. The present study showed improved cyclic fatigue life of endodontic instruments when activated by Reciproc Direct®.

The internal anatomy of danger zone of mandibular molars: A cone-beam computed tomography study.

AIM: The aim of this study was the assessment of the anatomical thickness of danger zone in the cervical third of mesial canals of mandibular molars. MATERIALS AND METHODS: Fifty mandibular molars were selected and scanned with cone-beam computed tomography. Data were compared using a length tool provided by scanner software. The measured areas were the mesial and distal walls of the cervical third of the mesial roots, which correspond to the safety and danger zones, respectively. In addition, dentin thickness at the furcation was evaluated. RESULTS: Dentin thicknesses of the safety zone were higher than in the danger zone in all teeth examined. The thinnest dentin of the safety zone was found at a point located 4 mm below the canal orifice, with a mean value of 1.03 mm; conversely, in the danger zone, the thinnest point was located 3 mm below the orifice, with a mean value of 0.81 mm. As for the distance from the pulp chamber floor to the furcation, the average value was 2.23 mm. CONCLUSION: These results show that mean thicknesses at the danger zone of mandibular molar mesial roots were <1.0 mm. These data reinforce the importance of understanding anatomy and the need for conservative preparations when assessing and instrumenting these root canals.

Mechanical Properties of Anatomic Finishing Files: XP-Endo Finisher and XP-Clean.

The aim of the present study was to evaluate the cyclic fatigue of two anatomic finishing files: XP-Endo Finisher and XP-Clean. Roughness pattern and the micro-hardness of the files were also assessed. Instruments were subjected to cyclic fatigue resistance measuring the time to fracture in an artificial stainless-steel canal with a 60° angle and a 5-mm radius of curvature. The fracture surface of all fragments was examined with a scanning electron microscope. The roughness of the working parts was quantified by using a profilometer and the micro-hardness test was carried out using a Vickers hardness tester. Results were statistically analyzed using a student´s t-test at a significance level of P < 0.05. Weibull analysis was also performed. XP-Endo Finisher presented significantly longer cyclic fatigue life than XP-Clean instruments (P<0.05). XP-Endo Finisher was able to withstand 1000% more cycles to fracture when compared to XP-Clean instruments. SEM visual inspection of the fracture surfaces revealed fractographic characteristics of ductile fracture in all tested instruments; wide-ranging forms of dimples were identified and no plastic deformation in the helical shaft of the fractured instruments was observed. When mean life was compared XP-Endo Finisher lasted longer than XP-Clean with a probability of 99.9%. XP-Endo Finisher instruments also exhibited significantly lower roughness than XP-Clean instruments (P<0.05). No differences in the micro-hardness was observed between the files (P>0.05). It can be concluded that XP-Endo Finisher instruments showed improved performance when compared with XP-Clean instruments, demonstrating higher cyclic fatigue resistance and lower roughness.

Fatigue resistance of endodontic instruments manufactured in NiTi CM Wire and in conventional NiTi alloy with eletrochemical treatment / Resistência à fadiga de instrumentos endodônticos fabricados em NiTi CM Wire e em niti convencional com tratamento eletroquìmico

ABSTRACT Objective: This study compared the fatigue behavior of endodontic instruments manufactured with conventional NiTi alloy electropolishing, RaCe (FKG Dentaire, LaChauxdeFonds, Switzerland), with instruments manufactured with NiTi CM ​​Wire subjected to thermomechanical treatment, in the manufacturing process, HyFlex CM (Coltène Whaledent, Cuyahoga Falls, Ohio, USA), both with similar geometry and dimensions in order to determine the influence of the manufacturing process in the fatigue resistance. Methods: The methodoly consisted of twenty HyFlex CM and RaCe instruments with D0 0.25 mm, taper 0.06 mm / mm, 25 mm length, both with triangular cross section. The fracture resistance was evaluated by static fatigue test, using a stainless artificial canal with 5mm of radius (86°), recording the time and calculating the number of cycles until fracture occurs (NCF). For statistical analysis the Student t test was used The fractured instruments surface was analyzed by SEM. Results: The NCF was significantly higher for HyFlex CM instruments in comparison with RaCe files (P˂0.05) being 1336% more resistant to fatigue. The analysis of the fractured surface by SEM showed ductile-kind morphological characteristics for both instruments and the absence of plastic deformation. Conclusion: HyFlex CM instruments present higher values ​​of NCF. Thus, it can be concluded that the thermal treatment to which these instruments with CM Wire alloy are submitted makes them more resistant to fracture than Race instruments manufactured with conventional NiTi alloy electropolishing.

RESUMO Objetivo: Este estudo comparou a vida em fadiga de instrumentos endodônticos fabricados com a liga de NiTi convencional com eletropolimento de superfície, RaCe (FKG Dentaire, LaChauxdeFonds, Suiça), com instrumentos fabricados com a liga de NiTi CM Wire, submetidos a tratamento termomecânico, no processo de fabricação, HyFlex CM (Coltene Whaledent, Cuyahoga Falls, Ohio, EUA), ambos com geometria e dimensões semelhantes, visando determinar a influência do processo de fabricação das ligas e do acabamento superficial na resistência à fadiga. Métodos: Foram utilizados vinte instrumentos HyFlex CM e RaCe com D0 0,25mm, conicidade 0,06mm/mm, 25mm de comprimento, ambos com seção transversal triangular. A resistência à fratura foi avaliada através de teste estático de fadiga ciclica, utilizando um canal artificial em aço-inoxidável com 5mm de raio (86°), sendo registrado o tempo e calculado o número de ciclos para ocorrer a fratura (NCF). Para análise estatística empregou-se o teste t de Student. As superfícies de fratura dos instrumentos foram analisadas em MEV. Resultados: O NCF foi significativamente maior para os instrumentos HyFlex CM em comparação com as limas RaCe (p˂0,05), sendo 1336% mais resistentes à fadiga. A análise das superfícies fraturadas em MEV revelou características morfológicas do tipo dúctil para ambos os instrumentos e ausência de deformação plástica. Conclusão: Os instrumentos HyFlex CM apresentaram valores mais elevados de NCF. Deste modo, pode-se concluir que o tratamento térmico a qual estes instrumentos com a liga CM Wire foram submetidos os torna mais resistentes à fratura do que os instrumentos Race, fabricados com a liga de NiTi convencional com eletropolimento.

Influência da conicidade e do ponto de imobilização na flexibilidade dos instrumentos de níquel-titânio rotatórios RaCe / Influence of taper and immobilization point on the flexibility of RaCe nickel-titanium rotary instruments

Objetivo: esse estudo comparou a flexibilidade de instrumentos de níquel-titânio rotatórios com diferentes conicidades, em diferentes diâmetros da haste helicoidal cônica (D3 e D6). Métodos: trinta instrumentos RaCe (FKG, La Chaux-de Fonds, Suíça), #40 (D0 = 40), com 25 mm de comprimento, foram divididos em três grupos (n = 10), de acordo com sua conicidade. No teste de flexão em cantiléver (45 graus), foram realizadas duas avaliações, com cargas aplicadas, em D3 e D6, para cada grupo. Resultados: a comparação das cargas aplicadas em D3 e D6 nos instrumentos RaCe com diferentes conicidades mostrou valores de carga máxima significativamente diferentes para flexionar os instrumentos: D3 < D6, com a flexibilidade em D3 maior do que em D6. A comparação das cargas aplicadas em D3 nos três grupos revelou diferenças significativas entre os grupos (p < 0,0001), enquanto o teste Student-Newman-Keuls (SNK) mostrou diferenças de flexibilidade entre os três grupos: 0,06 < 0,04 < 0,02mm/mm. O mesmo resultado foi encontrado na comparação da força aplicada em D6. Conclusões: a flexibilidade do instrumento aumenta com a redução da conicidade (p < 0,05) e diminui com o aumento no diâmetro do eixo helicoidal (p < 0,05).

Mechanical properties of anatomic finishing files: xp-endo finisher and xp-clean

Abstract The aim of the present study was to evaluate the cyclic fatigue of two anatomic finishing files: XP-Endo Finisher and XP-Clean. Roughness pattern and the micro-hardness of the files were also assessed. Instruments were subjected to cyclic fatigue resistance measuring the time to fracture in an artificial stainless-steel canal with a 60° angle and a 5-mm radius of curvature. The fracture surface of all fragments was examined with a scanning electron microscope. The roughness of the working parts was quantified by using a profilometer and the micro-hardness test was carried out using a Vickers hardness tester. Results were statistically analyzed using a student´s t-test at a significance level of P < 0.05. Weibull analysis was also performed. XP-Endo Finisher presented significantly longer cyclic fatigue life than XP-Clean instruments (P<0.05). XP-Endo Finisher was able to withstand 1000% more cycles to fracture when compared to XP-Clean instruments. SEM visual inspection of the fracture surfaces revealed fractographic characteristics of ductile fracture in all tested instruments; wide-ranging forms of dimples were identified and no plastic deformation in the helical shaft of the fractured instruments was observed. When mean life was compared XP-Endo Finisher lasted longer than XP-Clean with a probability of 99.9%. XP-Endo Finisher instruments also exhibited significantly lower roughness than XP-Clean instruments (P<0.05). No differences in the micro-hardness was observed between the files (P>0.05). It can be concluded that XP-Endo Finisher instruments showed improved performance when compared with XP-Clean instruments, demonstrating higher cyclic fatigue resistance and lower roughness.

Resumo O objetivo do presente estudo foi avaliar a fadiga cíclica de dois instrumentos finalizadores anatômicos: XP-Endo Finisher e XP-Clean. O padrão de rugosidade e a micro dureza dos instrumentos também foram avaliados. Os instrumentos foram submetidos à resistência à fadiga cíclica, medindo o tempo de fratura em um canal artificial de aço inoxidável com um ângulo de 60 ° e um raio de curvatura de 5 mm. A superfície de fratura de todos os fragmentos foi examinada com um microscópio eletrônico de varredura. A rugosidade dos instrumentos foi quantificada usando um perfilômetro e o teste de micro dureza foi realizado usando um testador de dureza Vickers. Os resultados foram analisados ​​estatisticamente usando o teste t de student em um nível de significância de p<0,05. A análise Weibull também foi realizada. XP-Endo Finisher apresentou vida de fadiga cíclica significativamente mais longa do que os instrumentos XP-Clean (p<0,05). XP-Endo Finisher foi capaz de suportar 1000% mais ciclos para fratura quando comparado aos instrumentos XP-Clean. A inspeção visual em microscópio eletrônico de varredura das superfícies de fratura revelou características fractográficas da fratura dúctil em todos os instrumentos testados. Não foi observada deformação plástica no eixo helicoidal dos instrumentos fraturados. Quando o tempo para a fratura foi comparado entre os instrumentos, o XP-Endo Finisher durou mais do que o XP-Clean com uma probabilidade de 99,9%. Os instrumentos XP-Endo Finisher também exibiram uma rugosidade significativamente menor do que os instrumentos XP-Clean (p<0,05). Não foram observadas diferenças na micro dureza entre os arquivos (p>0,05). Pode-se concluir que os instrumentos XP-Endo Finisher apresentaram desempenho melhorado em comparação com os instrumentos XP-Clean, demonstrando maior resistência à fadiga cíclica e menor rugosidade.

Removal of Root Canal Fillings in Curved Canals Using Either Mani GPR or HyFlex NT Followed by Passive Ultrasonic Irrigation.

This study compared the efficacy of HyFlex NT (HF; Coltene, New York, NY) and Mani GPR (MN; Mani Inc, Tokyo, Japan) systems followed by a supplementary approach with passive ultrasonic irrigation (PUI) in removing the filling material from curved root canals during retreatment. The mesial canals from 20 extracted mandibular molars with Vertucci type IV configuration were instrumented and obturated (N = 40). Each mesial canal was retreated using either HF or MN instruments, alternating the system used per canal from root to root. The final preparation size was 40/0.04 for both systems. The volume of canal filling material was assessed by means of micro-computed tomographic (micro-CT) imaging before and after retreatment, and the working time was recorded. Canals still showing remnants of filling material were subjected to a supplementary approach with PUI, and another micro-CT scan was taken. The percentage of filling material removed with MN instruments and HF was similar (95.5% and 92.7%, respectively) (P > .05). MN required significantly less time to remove the filling material (P < .05). The supplementary approach with PUI significantly enhanced the removal of filling material (P < .05). Both systems were equally effective in removing the root canal filling during retreatment. MN was faster than HF. The supplementary approach with PUI significantly improved filling material removal.

Physico-chemical and Biological Properties of a New Portland Cement-based Root Repair Material.

OBJECTIVE: To propose bismuth carbonate, a radiopacifying agent, as a new endodontic root repair material that was added to Portland cement (PC) at 2 wt%, 5 wt%, 10 wt% and 15 wt%, and physicochemical and biological properties of each formulation were evaluated in comparison to MTA-Angelus. METHODS: Mixed and powder samples were analysed by scanning electron microscopy (SEM) and X-ray power diffraction (XRD), and the semiquantitative constitution of the powder was determined by energy-dispersive spectrometer (EDS). Setting time was evaluated by Vicat needle and radiopacity analysed with digital X-ray. The pH of all tested materials was observed after immersion in water for 3, 24, 48, 72 and 168 h (or 7 days). Solubility and calcium release were measured after immersion in water for 24 h. A multiparametric assay XTT-NR-CVDE was used to evaluate the cytotoxicity of the materials in human periodontal ligament (HPDL) fibroblasts. HPDL fibroblasts were exposed to PC 15% and mineral trioxide aggregate (MTA), and the expression of proinflammatory cytokines (IL1A, IL6, IL8, TNF) and bone formation genes (ALP, COL1, RUNX2) was evaluated by real-time PCR. Mineralisation of HPDL fibroblasts cocultured with PC, PC 15% and MTA was evaluated with Von Kossa staining. RESULTS: PC-based groups presented more irregular and larger particles than MTA. PC and MTA showed similarities as observed by XRD and EDS. Setting time of PC-based groups was increased with the addition of bismuth carbonate. All tested materials were alkaline, and pH tended to reduce over time. All cements had solubility lower than recommended, with no difference between them (P>0.05) and showed calcium release. PC 15% had similar radiopacity when compared with MTA (P>0.05). Cell viability was higher for the tested materials than the positive control (P<0.001), but there was no difference when they were compared with negative control (P>0.05). Gene expression levels were similar for all tested groups (P>0.05). Analysed cements had positive Von Kossa staining. CONCLUSION: Overall, the addition of 15% of bismuth carbonate did not result in significant changes to its physicochemical and biological properties when compared with MTA, except for the setting time, and may be considered a potential substitute for MTA.

Geotecnologias na gestão de reservatórios: uma revisão e uma proposta de integração / Geotechnologies on water reservoir management: a review and an integration proposal

RESUMO Este trabalho teve como foco apresentar uma visão geral dos sistemas de informações geográficas (SIGs) e do sensoriamento remoto (SR), com ênfase nas suas aplicações para obtenção de informações da massa d'água. Essas informações são integradas ao Quadro da Diretiva da Água, e nesse sentido, busca-se propor a ligação dessas informações à Resolução nº 357/2005, de forma a servir de ferramenta para a tomada de decisão em uma gestão estratégica da qualidade da água, principalmente em grandes reservatórios. Assim, é realizada uma revisão integrando as geotecnologias à ciência limnológica e à gestão de reservatórios, ressaltando os possíveis potenciais da interação interdisciplinar. Por fim, é esquematizado um modelo integrando SIGs, SR e limnologia para o monitoramento e a gestão dos padrões de qualidade da água conforme a Resolução nº 357/2005.

ABSTRACT An overview of geographical information system (GIS) and remote sensing (RS) is the main focus of this work, that emphasizes their application to obtain water body information. This information is integrated to the Framework Directive, and in this way, seeks to propose the linkage of these information to the Resolution 357/2005, in order to serve as a tool for decision making in strategic management of water quality mainly in large reservoirs. Thus, a review that integrates geotechnology to limnological science and to reservoirs management was done, highlighting the possible potential of interdisciplinary integration. At the end, an integration model of GIS, RS and limnology is schematized for monitoring and management of water quality standards according to the Resolution 357/2005.

Surgical Strategy for Dermoid and Epidermoid Tumors of the Posterior Fossa - Experience with 21 Patients

Objective The aim of this paper is to describe our surgical strategy and technique and to identify the best management for posterior fossa dermoid and epidermoid tumors (PFDETs). Methods We retrospectively identified 21 consecutive patients (11 males and 10 females), with a mean age of 33.2 years, a mean follow-up of 6.1 years, and pathologically confirmed PFDETs. Total 17 patients were submitted to the extended retrosigmoid approach. This approach incorporates transverse sigmoid sinus exposure and a generous mastoidectomy. Results Gross total tumor removal was achieved in 16 (76.1%) cases, with no surgical mortality and a recurrence rate of 9.5%. Conclusions The surgical strategies used in this group of patients enabled the total removal of most tumors without surgical mortality and with minimal morbidity and recurrence rates. The extended retrosigmoid approach used is an alternative path regarding cranial base approaches. This approach is quick, simple and safe, and decreases the retraction of the cerebellum.

Objetivos O objetivo deste estudo é descrever a técnica operatória para a melhor abordagem dos tumores dermoides e epidermoides da fossa posterior. Métodos Foram analisados retrospectivamente 21 pacientes (11 masculinos e 10 femininos), com idade média de 33,2 anos e acompanhamento de 6,1 anos, com diagnóstico histopatológico de tumor dermoide ou epidermoide de fossa posterior. Nesse grupo, 17 pacientes foram submetidos a abordagem retrossigmoide estendida. Esta abordagem inclui exposição do seio transverso e sigmoide, além de ampla mastoidectomia. Resultados Remoção cirúrgica total foi alcançada em 16 (76,1%) casos sem mortalidade e com recidiva em 9,5% dos casos. Conclusões As abordagens cirúrgicas utilizadas nesta série permitiram a ressecção total na maioria dos pacientes, sem mortalidade cirúrgica e com morbidade e recorrência mínima. A craniotomia retrossigmoide estendida utilizada é uma boa alternativa para abordagens da base do crânio. É uma abordagem simples, rápida, segura, e que minimiza a retração do cerebelo.

Comportamento mecânico de instrumentos WaveOne e ProTaper em relação à torção, dureza e tenacidade / Mechanical properties of WaveOne and ProTaper instruments in relation to torsion, hardness and toughness

Objetivo: esse estudo teve como objetivo avaliar a resistência à fratura por torção de duas marcas de instrumentos mecanizados de NiTi, com formas geométricas distintas e produzidas por ligas metálicas diferentes. Métodos: quinze instrumentos WaveOne Large e quinze ProTaper F4 foram selecionados e submetidos aos ensaios mecânicos de torção, microdureza Vickers e tenacidade. No ensaio de torção, foram avaliados a deformação angular até a fratura e o torque máximo. As superfícies fraturadas e as hastes helicoidais dos instrumentos foram analisadas por meio de microscopia eletrônica de varredura (MEV). Resultados: os valores do ângulo máximo em torção foram maiores para o ProTaper, enquanto o torque máximo em torção (N/cm) foi maior para o WaveOne. Os valores de microdureza Vickers foram maiores para a liga NiTi M-Wire, enquanto o grupo controle apresentou maior tenacidade. O teste t de Student demonstrou diferença significativa nos ensaios de torção (p < 0,05), tenacidade e microdureza Vickers. A análise do MEV revelou deformação plástica ao longo das hélices helicoidais de todos os instrumentos fraturados e fratura tipo dúctil. Conclusão: os instrumentos fabricados em NiTi M-Wire apresentaram maior resistência à fratura por torção e maior microdureza, em comparação aos de NiTi convencional. Devido ao maior ângulo de torção do ProTaper e à maior deformação até a fratura, esses parâmetros tornam esse instrumento mais seguro do ponto de vista clínico.

Statistical tools for the temporal analysis and classification of lung lesions.

BACKGROUND AND OBJECTIVE: Lung cancer remains one of the most common cancers globally. Temporal evaluation is an important tool for analyzing the malignant behavior of lesions during treatment, or of indeterminate lesions that may be benign. This work proposes a methodology for the analysis, quantification, and visualization of small (local) and large (global) changes in lung lesions. In addition, we extract textural features for the classification of lesions as benign or malignant. METHODS: We employ the statistical concept of uncertainty to associate each voxel of a lesion to a probability that changes occur in the lesion over time. We employ the Jensen divergence and hypothesis test locally to verify voxel-to-voxel changes, and globally to capture changes in lesion volumes. RESULTS: For the local hypothesis test, we determine that the change in density varies by between 3.84 and 40.01% of the lesion volume in a public database of malignant lesions under treatment, and by between 5.76 and 35.43% in a private database of benign lung nodules. From the texture analysis of regions in which the density changes occur, we are able to discriminate lung lesions with an accuracy of 98.41%, which shows that these changes can indicate the true nature of the lesion. CONCLUSION: In addition to the visual aspects of the density changes occurring in the lesions over time, we quantify these changes and analyze the entire set using volumetry. In the case of malignant lesions, large b-divergence values are associated with major changes in lesion volume. In addition, this occurs when the change in volume is small but is associated with significant changes in density, as indicated by the histogram divergence. For benign lesions, the methodology shows that even in cases where the change in volume is small, a change of density occurs. This proves that even in lesions that appear stable, a change in density occurs.

The dentin thickness remaining in the risk zone of mandibular molars after cervical preflaring with four methods / A espessura da dentina remanescente na zona de perigo após o pré-alargamento com quatro métodos

Introduction: Cervical preflaring is an important step of the canal system instrumentation, but can lead to excessive enlargement or root perforation. Objective: Evaluate the remaining dentin thickness in the mandibular molars of mesial roots using cone beam computed tomography: Gates-Glidden (crown-down); Gates-Glidden (step-back); LA Axxess and Easy Pro-Design. Material and method: Were selected 40 lower molars mesial roots, which were scanned in a cone beam CT scanner before and after preparation. Were obtained five sections of the CT images with an interval of 1 mm from the furcation, and measured the thickness variation between the root canal to the root external portion in analysis software. Result: The evaluation of the different levels showed no significance within the same group for the Gates-Glidden group. On the other hand, were observed difference for LA Axxess (p=0.002) and Easy Pro-Design (p=0.005). In the intergroup analysis, were observed difference in all levels, especially for Gates-Glidden in the ascendant order (ANOVA and Tukey). Conclusion: Within the limitations of these study, is possible to conclude that the protocol with greater wear in the cervical risk area was the Gates-Glidden in step-back sequence, as the other groups were equivalent (p>0.05).

Introdução: O preparo cervical é uma etapa importante da instrumentação do sistema de canais, mas pode levar ao alargamento excessivo ou rasgo da raiz. Objetivo: Avaliar, em tomografia computadorizada cone beam, da espessura remanescente de dentina cervical da raiz mesial de molares inferiores, após o preparo com diferentes técnicas: Gates-Glidden (ordem crescente); Gates-Glidden (ordem decrescente); LA Axxess e Easy Pro-Design. Material e método: Foram selecionadas 40 raízes mesiais de molares inferiores, que foram escaneadas em tomógrafo cone beam antes e após o preparo. Das imagens tomográficas foram obtidos cinco cortes com intervalo de 1 mm a partir da furca e, então, mensurada a variação da espessura entre o canal radicular até a porção externa da raiz em software de análise. Resultado: Avaliação dos diferentes níveis demonstraram ausência de significância dentro do mesmo grupo para o grupo das Gates-Glidden. Por outro lado, foi notada diferença para LA Axxess (p=0,002) e para Easy Pro-Design (p=0,005). Na avaliação entre os grupos, foi observada diferença em todos os níveis, sobretudo, para Gates-Glidden na ordem crescente (ANOVA e Tukey). Conclusão: Considerando as limitações desse estudo, concluiu-se que o protocolo que apresentou maior desgaste da área de perigo cervical foi o da Gates-Glidden em ordem crescente, sendo que os demais grupos foram equivalentes (p>0,05).

Bending Resistance and Cyclic Fatigue Life of Reciproc, Unicone, and WaveOne Reciprocating Instruments.

INTRODUCTION: This study evaluated the bending resistance and cyclic fatigue life of a new single-file reciprocating instrument (Unicone; Medin, Nové Mesto na Morave, Czech Republic). Reciproc (VDW, Munich, Germany) and WaveOne (Dentsply Maillefer) instruments were used as references for comparison. METHODS: Flexibility was determined by 45° bending tests using a universal testing machine. The cyclic fatigue test was performed using a custom-made device. For this test, an artificial canal with a 60° angle and a 5-mm radius of curvature was used. Scanning electron microscopic analysis was performed to determine the mode of fracture and possible deformations at the helical shaft. Statistical analysis for the bending resistance test was performed using parametric methods (ie, 1-way analysis of variance). Post hoc pair-wise comparisons were performed using the Tukey test for multiple comparisons (P < .05). Weibull analysis was used to calculate the mean life, beta, and eta parameters. RESULTS: Reciproc presented significantly lower bending resistance than the other tested systems (P < .05), whereas no differences were observed between WaveOne and Unicone (P > .05). When mean life was compared among the brands, Reciproc lasted longer than WaveOne with a probability of 99.9%, longer than Unicone in the "RECIPROC ALL" mode with a probability of 99.9%, and longer than Unicone in the "WAVEONE ALL" mode with a probability of 99.9% (all statistically significant). Moreover, WaveOne lasted longer than Unicone in the "RECIPROC ALL" mode with a probability of 98.5% and longer than Unicone in the "WAVEONE ALL" mode with a probability of 99.8% (all statistically significant). Finally, Unicone in the "RECIPROC ALL" mode lasted longer than Unicone in the "WAVEONE ALL" mode with a probability of 95.3% (statistically significant). CONCLUSIONS: The new reciprocating instrument Unicone showed lower cyclic fatigue resistance compared with Reciproc R25 and WaveOne Primary files.

Bending resistance and cyclic fatigue of a new heat-treated reciprocating instrument.

The current study aimed to evaluate the bending resistance and the cyclic fatigue life of a new heat-treated reciprocating instrument (ProDesign R). Untreated ProDesign R, Reciproc R25, and WaveOne Primary instruments were used as reference instruments for comparison. The bending resistance was performed in ten instruments of each system by using a universal testing machine and a proper apparatus. The cyclic fatigue resistance was tested measuring the number of cycles to failure in an artificial stainless steel canal. Scanning electron microscopy analysis was performed to determine the mode of fracture and possible deformations at the helical shaft. Statistical analysis was performed by using parametric methods; one-way analysis of variance plus post hoc pair-wise Tukey test for multiple comparisons (p < 0.05). Untreated ProDesign R presented significantly higher bending resistance than the other tested systems (p < 0.05). No differences were observed between ProDesign R and Reciproc files regarding the bending resistance (p > 0.05). Moreover, ProDesign R revealed a significantly longer cyclic fatigue life (p < 0.05). In contrast, Untreated ProDesign R and WaveOne instruments presented significantly lower cyclic fatigue life than Reciproc (p < 0.05). The new heat-treated reciprocating instrument ProDesign R have higher cyclic fatigue resistance than Untreated ProDesign R, Reciproc, and WaveOne instruments. ProDesign R and Reciproc were significantly more flexible than Untreated ProDesign R and WaveOne files. SCANNING 38:837-841, 2016. © 2016 Wiley Periodicals, Inc.

Influence of Surface Roughness on the Fatigue Life of Nickel-Titanium Rotary Endodontic Instruments.

INTRODUCTION: The goal of the present study was to evaluate the influence of surface grooves (peaks and valleys) resulting from machining during the manufacturing process of polished and unpolished nickel-titanium BR4C endodontic files on the fatigue life of the instruments. METHODS: Ten electropolished and 10 unpolished endodontic files were provided by the manufacturer. Specimens were from the same batch, but the unpolished instruments were removed from the production line before surface treatment. The instruments were evaluated with a profilometer to quantify the surface roughness on the working part of the instruments. Then the files were subjected to rotating bending fatigue tests. RESULTS: Analysis with the profilometer showed that surface grooves were deeper on the unpolished instruments compared with their electropolished counterparts. In the rotating bending fatigue test, the mean and standard deviation for the number of cycles until fracture (NCF) were greater for instruments with less pronounced grooves. Student t test revealed significant differences in all tests (P < .05). CONCLUSIONS: The results from the present study showed that the depth of the surface grooves on the working part affected the NCF of the instruments tested; the smaller the groove depth, the greater the NCF.

Bending Resistance and Cyclic Fatigue Life of a new Single-File Reciprocating Instrument Waveone Gold.

OBJECTIVE: The present study aimed to evaluate the bending resistance and cyclic fatigue fracture resistance of a new single-file reciprocating instrument called WaveOne Gold. Reciproc and WaveOne instruments were used as references for comparison. METHODS: Sixty 25-mm NiTi instruments (Reciproc R25, WaveOne Primary and WaveOne Gold Primary) were tested. Flexibility was determined by applying 45° bending tests using a universal testing machine (n=10). A custom-made device was used during cyclic fatigue test (n=10), comprising a stainless steel artificial canal measuring 1.4 mm in diameter, 19 mm in total length with an 86° angle and 6 mm radius of curvature. Possible deformations at the helical shaft and mode of fracture were evaluated using scanning electron microscopy analysis. Statistical analysis was performed using one-way analysis of variance. Post hoc pair-wise comparisons were performed using Tukey's test for multiple comparisons (P<0.05). RESULTS: WaveOne presented significantly higher bending resistance than the other tested systems (P<0.05), whereas Reciproc presented the lowest bending resistance (P<0.05). Reciproc revealed a significantly longer cyclic fatigue fracture resistance than the other systems (P<0.05). CONCLUSION: Although WaveOne Gold presented higher flexibility than WaveOne, no differences in the resistance to fatigue were observed between both systems. The Reciproc files were more flexible and resistant to fatigue for the angle of curvature of 86° and 6 mm radius than WaveOne and WaveOne Gold files.

Comportamento espacial da clorofila-a no reservatório de Itaparica, rio São Francisco / Spatial behavior of chlorophyll-a in Itaparica reservoir, São Francisco River

RESUMONa análise do estado trófico de um corpo hídrico torna-se fundamental o conhecimento da concentração de clorofila-a. Esse trabalho tem como objetivo determinar e avaliar o comportamento da clorofila-a no reservatório de Itaparica, localizado no sub-médio São Francisco. Para esse fim, utilizou-se de imagem Landsat-TM, na qual foram utilizadas as bandas de 1 a 5 e 7. O modelo aplicado foi escrito em linguagem LEGAL-SPRING 5.2. A partir da imagem da clorofila-a realizou-se o fatiamento do corpo hídrico em seis classes concentração. O valor mínimo foi de <1 mg/L e o maior foi de 249,5 mg/L. As classes que obtiveram maior área foram de 0 a 5 mg/L com 27,4%, seguida da classe 5 a 10 mg/L com 24,6% da área total do reservatório, conforme observado por histograma. Por meio da análise gráfica de pontos situados ao longo do reservatório verifica-se que a concentração da clorofila-a aumenta da região fluvial para região lacustre e a partir dos contatos dos riachos com o reservatório. Em futuros estudos há necessidade de se validar os valores encontrados com dados de campo de forma a verificar a precisão do mapeamento para o reservatório em estudo, observando dia e horário da passagem do sensor.

ABSTRACTIn the analysis of trophic state of the water body is fundamental to know chlorophyll-a concentration. Thus, this work has as main aim to determinate and to assess the behavior of chlorophyll-a in the Itaparica reservoir, São Francisco river. This way, we used Landsat-TM imagery, in which it was used bands from 1 to 5 and 7. The algorithm used was written in LEGAL/SPRING 5.2. From the chlorophyll-a result was held slicing the water body in six concentration classes. As observed by histogram, the minimum value of Chl-a was < 1 mg/L and the highest was 249.5 mg/L. The classes that had the biggest area were Classe 01 (0-5 mg/L) with 27.4%, followed by Classe 02 (5-10 mg/L) with 24.6% of the total area of the study area. Through graphical analysis of points located along the reservoir it was possible to verify that chlorophyll concentration augmented from fluvial to lacustrine region and from the contact of streams with reservoir. In the next studies there is a need to validate the values with field data in order to verify the mapping accuracy in this reservoir, taking into account the day and also the transit time of the sensor.

Flexibilidade e fadiga cíclica de instrumentos fabricados com métodos diferentes / Flexibility and resistance to cyclic fatigue of instruments manufactured by different methods

Objetivo: o presente estudo comparou o comportamento mecânico de instrumentos de níquel-titânio que apresentavam forma geométrica semelhante, porem, produzidos por métodos de fabricação diferentes. Métodos: foram usados, para o teste de flexibilidade e de flexão rotativa, vinte instrumentos 25/0,06 RaCe (FKG Dentaire, La Chaux-de-Fonds, Suíça), com 25 mm de comprimento, produzidos por fio de NiTi convencional (usinados); 20 instrumentos endodônticos especiais 25/0,06 Twisted File (TF) (SybronEndo, Orange, EUA), com 27 mm de comprimento, fabricados por torção; e 20 instrumentos endodonticos 25/0,06 ProFile Vortex (Dentsply Tulsa Dental, Tulsa, EUA), com 25mm de comprimento, feitos com liga M-Wire. Cada grupo dos respectivos ensaios teve 10 instrumentos de cada fabricante. Resultados: o teste paramétrico ANOVA mostrou que houve diferença significativa entre os valores de carga máxima, na seguinte ordem decrescente: ProFile Vortex > RaCe > TF (p < 0,01). Com o ensaio de flexão rotativa, o teste paramétrico ANOVA, com nível de significância de 1%, mostrou que os instrumentos RaCe tiveram uma diferença significativa menor para a fratura do que os instrumentos Pro-File Vortex, que foram significativamente inferiores aos instrumentos TF, com relação ao tempo e ao numero de ciclos (p < 0,01). Conclusão: os instrumentos TF foram mais flexiveis do que os instrumentos RaCe, que foram menos resistentes a flexão do que os instrumentos ProFile Vortex. Considerando-se o ensaio de flexão rotativa, os instrumentos TF apresentaram um desempenho significativamente superior com relação ao tempo e ao numero de ciclos para a fratura (NCF) do que os outros instrumentos testados.